| Product Name | Calcium Sulfate Whisker |
| 产品名称 | 硫酸钙晶须 |
| Chemical Formula | CaSO₄ |
| Crystal Form | Anhydrite (α-CaSO₄) |
| 晶型 | 硬石膏型(α型硫酸钙) |
| Appearance | White needle-like powder |
| 外观 | 白色针状粉末 |
| Crystal Shape | Single crystal needle/whisker |
| 晶体形态 | 单晶针状/晶须 |
| Diameter | 1 – 4 μm |
| Length | 10 – 300 μm |
| Aspect Ratio | 40 – 80 |
| Surface | Smooth, defect-free |
| 表面 | 光滑、无缺陷 |
| Parameter / 指标 | Value / 实测值 | Reference Range* / 参考区间* | Customer Benefit / 对客户的意义 |
|---|---|---|---|
| Purity / 纯度 | ≥ 98% | 95 – 97% | Higher reinforcement efficiency, fewer impurities affecting polymer matrix |
| Whiteness / 白度 | ≥ 95% | 92 – 95% | Low colour impact on the compound; suited to white and light-coloured systems |
| Heat Resistance / 耐热温度 | 1000°C | 600 – 800°C | Property of the whisker material itself; stable through normal compounding temperatures. It is not the service temperature of the final composite. |
| Melting Point / 熔点 | 1450°C | — | Far exceeds all polymer processing temperatures |
| Density / 密度 | 2.69 g/cm³ | 2.5 – 2.9 g/cm³ | Mineral-filler-level density. Not lower than glass fibre (≈2.55 g/cm³); part-weight effects must be calculated for each formulation. |
| Mohs Hardness / 莫氏硬度 | 2 – 4 | — | Low abrasion on screws, barrels, and molds vs. mineral fillers |
| pH Value / pH值 | 6 – 7 | — | Neutral, compatible with most polymer systems and additives |
* The reference ranges are general figures quoted in the calcium sulfate whisker literature and market; they are not the result of a Hancore survey or a comparative Hancore test. The "Value" column reflects the published HM003 product specification.
* 参考区间为硫酸钙晶须一般文献与市场常见数值,并非我方调研或对比测试结果。"实测值"列为HM003已发布的产品规格。
| Resin System / 树脂体系 | Loading Level / 添加量 | Technical Evaluation Areas / 技术评估项 | Comparison Basis / 对比基准 |
|---|---|---|---|
| PA6 / PA66 | To be established by trial | Tensile and flexural properties, notched impact, heat deflection temperature, warpage | Unfilled resin and the customer's current glass-filled grade |
| PP (homopolymer / copolymer) | To be established by trial | Stiffness, shrinkage and shrinkage anisotropy, surface finish, HDT | Unfilled PP and the current CaCO₃ or talc compound |
| PVC | To be established by trial | Profile rigidity, impact strength, surface quality, filler loading window | Current CaCO₃-filled formulation |
| PBT / PET | To be established by trial | Tensile and flexural retention after drying, HDT, mould shrinkage, gate appearance | Existing mineral-filled or glass-filled grade |
| Status | Laboratory research direction |
| 状态 | 实验室研究方向 |
| Evaluation areas | Compressive and flexural strength of the reinforced monolith |
| 评估项 | 增强单体的抗压与弯曲强度 |
| Evaluation areas | Thermal conductivity and density change versus unreinforced aerogel |
| 评估项 | 与未增强气凝胶对比的导热系数与密度变化 |
| Published data | None — literature figures are not transferable to Hancore grades |
| 发布数据 | 无 — 文献数据不能套用于Hancore产品 |
| Status | Investigational application |
| 状态 | 探索性应用 |
| Evaluation areas | Spectral reflectance of the cured coating film |
| 评估项 | 固化涂膜的光谱反射率 |
| Evaluation areas | Pigment loading, film thickness and binder system effects |
| 评估项 | 颜料体积浓度、膜厚与树脂体系的影响 |
| Published data | None — reflectance must be measured on the customer's coating |
| 发布数据 | 无 — 反射率需以客户涂料实测 |
| Application | Roof coatings, films |
| 应用 | 屋顶涂料、隔热膜 |
| Evaluation areas | Profile rigidity and impact strength versus the current CaCO₃ formulation |
| 评估项 | 与现用碳酸钙配方对比的型材刚性与冲击强度 |
| Evaluation areas | Surface quality and filler loading window in extrusion |
| 评估项 | 挤出体系中的表面质量与填充量窗口 |
| Flame behaviour | Assessed to ISO 4589 / GB/T 2406 on the customer's compound |
| 燃烧性能 | 按ISO 4589/GB/T 2406以客户物料实测 |
| Published data | None — no MPa or LOI figures are published without a test report |
| 发布数据 | 无 — 没有测试报告不发布MPa或LOI数值 |
| Application | WPC, SPC flooring, wall panels |
| 应用 | WPC、SPC地板、墙板 |
| Grade / 型号 | Type / 类型 | Purity / 纯度 | Whiteness / 白度 | Diameter / 直径 | Length / 长度 | Aspect Ratio / 长径比 | Best For / 最佳应用 |
|---|---|---|---|---|---|---|---|
| HM003 | Standard / 标准型 | ≥98% | ≥95% | 1–4 μm | 10–300 μm | 40–80 | General compounding, engineering plastics |
| HM003S | Surface-Treated / 表面处理型 | To be confirmed / 待确认 | To be confirmed / 待确认 | To be confirmed / 待确认 | To be confirmed / 待确认 | To be confirmed / 待确认 | Surface-treated grade; application suitability established only by trial |
| Your Application / 您的应用 | Grade to Trial / 建议试制型号 | Loading / 添加量 | Evaluation Areas / 评估方向 |
|---|---|---|---|
| PP/PE Compounding | HM003 | To be established by trial | Stiffness, warpage and shrinkage anisotropy, surface finish, cost balance |
| PA/PBT Engineering Plastics | HM003 (HM003S only after its parameters are confirmed) | To be established by trial | Tensile/flexural properties, notched impact, HDT, dispersion |
| 3D Printing Filament | To be determined by trial | To be established by trial | Evaluation areas: dispersion, interlayer bonding, surface quality |
| Automotive Parts | HM003 (grade to be confirmed per part requirement) | To be established by trial | Dimensional stability, surface replication, heat ageing, part-level validation |
| PVC Building Materials | HM003 | To be established by trial | Profile rigidity, impact strength, surface quality; flame behaviour tested per applicable standard |
| Density / 密度 | 2.69 g/cm³ |
| Heat Resistance / 耐热 | 1000°C (whisker material only / 仅晶须材料本体) |
| Melting Point / 熔点 | 1450°C |
| Mohs Hardness / 莫氏硬度 | 2 – 4 |
| pH Value / pH值 | 6 – 7 |
| Crystal System / 晶系 | Orthorhombic / 正交晶系 |
| Solubility / 溶解性 | Insoluble in water, organic solvents |
| 溶解性 | 不溶于水和有机溶剂 |
| Toxicity / 毒性 | Non-toxic, food-contact safe |
| 毒性 | 无毒,食品接触安全 |
| Item / 项目 | HM003 | HM003S |
|---|---|---|
| Surface / 表面状态 | Standard, as produced / 标准型(出厂状态) | Surface-treated / 表面处理型 |
| Purity / 纯度 | ≥98% | To be confirmed / 待确认 |
| Diameter / 直径 | 1–4 μm | To be confirmed / 待确认 |
| Aspect Ratio / 长径比 | 40–80 | To be confirmed / 待确认 |
| Dispersion in polymer / 分散性 | Not quantified — trial-dependent / 未量化,取决于试制 | To be confirmed / 待确认 |
| Released TDS / 已发布TDS | Available on request / 可索取 | Not yet released / 尚未发布 |
| Parameter / 指标 | CSW Fibers / 硫酸钙晶须 | Glass Fiber / 玻璃纤维 | Advantage / 优势 |
|---|---|---|---|
| Density / 密度 | 2.69 g/cm³ | 2.55 g/cm³ | Comparable density; CSW is slightly higher |
| Mohs Hardness | 2 – 4 | 6 – 7 | Lower filler hardness is expected to reduce screw and barrel wear; confirm on the line |
| Surface Finish | Short fibre length | Fiber blush common | Lower fibre blush potential; surface class is defined by the part specification |
| Cost | Mineral-filler pricing | Reinforcement pricing | Cost balance depends on resin, loading and target properties |
| Aspect Ratio | 40 – 80 | Variable | Narrow, consistent whisker geometry as supplied |
| Skin Irritation | Non-biopersistent mineral fibre | Known irritant | Handling profile differs from glass fibre; see the SDS |
| Recyclability | Mineral filler in the same resin | Difficult | No composite test data published; regrind behaviour to be trialled |
| Parameter / 指标 | CSW Fibers / 晶须 | Short Carbon Fiber / 短切碳纤维 | Comment / 说明 |
|---|---|---|---|
| Wear behaviour (PEEK) | Evaluated as a tribological filler in published studies | Established wear filler | Tribo-test results in the literature are specific to their own formulations; Hancore publishes no wear-rate figures |
| 磨损性能(PEEK) | 公开研究中作为摩擦学填料被评估 | 成熟的耐磨填料 | 文献摩擦学结果仅对应其自身配方;Hancore不发布磨损率数值 |
| Cost | Mineral-filler pricing | High | Cost comparison to be calculated per compound |
| Color | White | Black only | Light-coloured and pigmentable compounds |
| EMI Shielding | None (electrically insulating) | Conductive | Carbon fibre is the choice where conductivity is required |
| Processing | Standard compounding equipment | Equipment wear considerations | Confirm on the customer's line |
| Property / 项目 | HM003 (Standard) | HM003S (Surface-Treated) | Basis / 依据 |
|---|---|---|---|
| Product status / 产品状态 | Offered / 在售 | Offered / 在售 | Product range / 产品系列 |
| Surface condition / 表面状态 | As produced / 出厂状态 | Surface-treated / 表面处理 | Grade definition / 型号定义 |
| Tensile strength in compound / 复合材料拉伸强度 | Not published / 未发布 | To be confirmed / 待确认 | Requires a documented test on the customer resin / 需客户树脂体系实测 |
| Flexural strength in compound / 弯曲强度 | Not published / 未发布 | To be confirmed / 待确认 | Requires a documented test / 需实测 |
| Impact strength in compound / 冲击强度 | Not published / 未发布 | To be confirmed / 待确认 | Requires a documented test / 需实测 |
| Dispersion / 分散性 | Trial-dependent / 取决于试制 | To be confirmed / 待确认 | Microscopy of the extrudate / 挤出样条显微观察 |
| Moisture uptake / 吸水率 | To be confirmed / 待确认 | To be confirmed / 待确认 | QC report pending / QC报告待发布 |
| Melt flow of the compound / 复合物流变 | Trial-dependent / 取决于试制 | To be confirmed / 待确认 | Capillary rheometer on the trial compound / 试物料毛细管流变 |
| Purity / 纯度 | ≥98% | To be confirmed / 待确认 | HM003 confirmed only / 仅HM003已确认 |
| Aspect ratio (as supplied) / 长径比(出厂) | 40–80 | To be confirmed / 待确认 | HM003 confirmed only / 仅HM003已确认 |
| Parameter / 参数 | Recommendation / 建议 | Notes / 说明 |
|---|---|---|
| Feeding Method / 喂料方式 | Side feeder (commonly used starting point) | Introducing the filler downstream limits shear exposure and helps retain whisker aspect ratio; compare routes on the line |
| 喂料方式 | 侧向喂料(常用起始方案) | 在下游加入填料可减少剪切暴露、有利于保留晶须长径比;不同喂料方式需在产线上对比验证 |
| Screw Speed / 螺杆转速 | 200 – 400 RPM | Moderate shear to limit whisker breakage; specific value depends on line and throughput |
| 螺杆转速 | 200 – 400 RPM | 中等剪切以控制晶须断裂;具体数值取决于设备与产量 |
| Melt Temperature / 熔体温度 | 200 – 280°C | Set by the base polymer (PP: 200-220°C, PA: 260-280°C), not by the filler |
| Loading Level / 添加量 | 10 – 30 wt% as a trial starting window | Starting point for trials only — not an optimum. Higher loading generally raises stiffness but can reduce impact strength; confirm by test |
| 添加量 | 10 – 30 wt% 作为试制起始区间 | 仅为试制起点,不是最佳值。提高添加量通常会增加刚性但可能降低冲击强度,需实测确认 |
| Drying / 干燥 | 100-120°C, 2 hours | Remove surface moisture before compounding; adjust to the feeder and resin |
| 干燥 | 100-120°C,2小时 | 共混前去除表面水分;按加料器与树脂情况调整 |
| Compatibilizer / 相容剂 | Selected by the customer's formulation | Maleated PP/PE is commonly evaluated for non-polar matrices; dosage is part of the customer's recipe |
| Polymer / 聚合物 | CSW Trial Window / 晶须试制区间 | Compatibilizer / 相容剂 | Commonly Evaluated Additives / 常评估的其他助剂 |
|---|---|---|---|
| PP / 聚丙烯 | 20 – 30 wt% (window only) | PP-g-MA, dosage per customer recipe | Antioxidant, lubricant |
| PA6 / 尼龙6 | 15 – 25 wt% (window only) | Often not required — verify | Heat stabilizer |
| PE / 聚乙烯 | 15 – 20 wt% (window only) | PE-g-MA, dosage per customer recipe | Antioxidant |
| PVC / 聚氯乙烯 | 10 – 15 wt% (window only) | CPE or acrylic processing aid, per compound | Stabilizer, lubricant |
| ABS | 10 – 20 wt% (window only) | Often not required — verify | Impact modifier |
| PLA (3D printing filament) | To be established by trial | Not required | Nucleating agent, if needed |
| Packaging / 包装 | Net Weight / 净重 | Dimensions / 尺寸 | Suitability / 适用 |
|---|---|---|---|
| Paper Bag (inner PE liner) | 12.5 kg / bag | 500×350×100 mm | Standard orders, easy handling |
| 纸袋(内衬PE袋) | 25公斤/袋 | 500×350×100 mm | 标准订单,便于搬运 |
| Big Bag (Ton Bag) | 500 – 1000 kg | 900×900×1200 mm | Bulk orders, cost-efficient |
| 吨袋 | 500 – 1000公斤 | 900×900×1200 mm | 大批量订单,经济高效 |
| Custom Packaging | Per request | Per request | OEM, special requirements |
| 定制包装 | 按需 | 按需 | OEM、特殊要求 |